Butterfly valve structure and common problem analysis

[ad_1]

Flap valve is another name for butterfly valve, which belongs to a kind of valve with relatively simple structure among control valves. As a component used to realize the on-off and flow control of the pipeline system, the butterfly valve has been widely used in many fields such as petroleum, chemical industry, metallurgy, hydropower and so on. In the known butterfly valve technology, the sealing form mostly adopts the sealing structure, and the sealing material is rubber, polytetrafluoroethylene, etc. Due to the limitation of structural characteristics, it is not suitable for industries such as high temperature resistance, high pressure, corrosion resistance and wear resistance.

Butterfly valve structure and common problem analysis


A relatively advanced butterfly valve is a triple eccentric metal hard-sealed butterfly valve. The valve body and the valve seat are connected components, and the sealing surface layer of the valve seat is surfacing with temperature-resistant and corrosion-resistant alloy materials. The multi-layer soft stacked sealing ring is fixed on the valve plate. Compared with the traditional butterfly valve, this butterfly valve has high temperature resistance, easy operation, and no friction when opening and closing. When closing, the torque of the transmission mechanism increases to compensate the sealing, which improves the butterfly valve. The advantages of excellent sealing performance and extended service life.

However, this butterfly valve still has the following three problems during use:
1. Restricted by structural conditions, the structure is not suitable for valves with a diameter below DN200, because the overall structure of the valve plate is too thick and the flow resistance is large.

2. Since the multi-layer soft and hard stacked sealing ring is fixed on the valve plate, when the valve plate is normally open, the medium forms a positive scouring on its sealing surface, and the soft sealing belt in the metal sheet interlayer is scoured, which directly affects the sealing performance.
3. Due to the principle of the triple eccentric structure, the sealing between the sealing surface of the valve plate and the valve seat relies on the torque of the transmission device to press the valve plate to the valve seat. In the positive flow state, the higher the medium pressure, the tighter the seal squeezes. When the medium in the flow channel flows back, the unit positive pressure between the valve plate and the valve seat is less than the medium pressure as the medium pressure increases, and the seal begins to leak.
The high-performance triple eccentric bidirectional hard sealing butterfly valve is characterized in that: the valve seat sealing ring is composed of multi-layer stainless steel sheets on both sides of the soft T-shaped sealing ring. The sealing surface of the valve plate and the valve seat is an inclined conical structure, and the temperature and corrosion resistant alloy material is surfacing on the inclined conical surface of the valve plate; the spring fixed between the adjusting ring pressure plates and the adjusting bolts on the pressure plate are assembled together.
This structure effectively compensates the tolerance zone between the shaft sleeve and the valve body and the elastic deformation of the valve stem under medium pressure, and solves the sealing problem of the valve during the two-way exchange of medium conveying. The sealing ring is composed of multi-layer stainless steel sheets on both sides of the soft T-shaped, which has the dual advantages of metal hard sealing and soft sealing, and has zero leakage sealing performance under low temperature and high temperature conditions.

The test proves that when the pool is in a positive flow state (the direction of medium flow is the same as the direction of rotation of the butterfly plate), the pressure on the sealing surface is generated by the torque of the transmission device and the action of the medium pressure on the valve plate. When the positive medium pressure increases, the tighter the oblique conical surface of the valve plate and the sealing surface of the valve seat are, the better the sealing effect will be. When the flow is reversed, the sealing between the valve plate and the valve seat depends on the torque of the driving device, so that the valve plate is pressed against the valve seat. With the increase of the reverse medium pressure, when the unit positive pressure between the valve plate and the valve seat is less than the medium pressure, the deformation stored by the spring of the adjusting ring after being loaded can compensate the tight pressure between the valve plate and the valve seat sealing surface play an automatic compensation role. Therefore, the utility model does not install the soft and hard multi-layer sealing ring on the valve plate as in the prior art, but is directly installed on the valve body, and adding an adjusting ring between the pressure plate and the valve seat is an ideal two-way hard sealing method .
The above content is the analysis of the butterfly valve structure and common problems brought to you today by Little Valve. After reading it, you should have some understanding of the basic structure of the butterfly valve, and the common problems will be solved very well when you encounter them again. You have shared a lot of knowledge about butterfly valves, please continue to pay attention to Baival.com~

[ad_2]

Share:

Send Us A Message

More Posts

Added to wishlistRemoved from wishlist 0
Add to compare
Metal Seated Lift Plug Valve manufacturer
Added to wishlistRemoved from wishlist 0
Add to compare
steam trap manufacturer
Added to wishlistRemoved from wishlist 0
Add to compare
Cast Steel Gate Valve-API
Added to wishlistRemoved from wishlist 0
Add to compare
Forged Steel Gate Valve
Added to wishlistRemoved from wishlist 0
Add to compare
Resilient Seat Gate Valve-DIN
Added to wishlistRemoved from wishlist 0
Add to compare
Resilient Seat Gate Valve-BS
Added to wishlistRemoved from wishlist 0
Add to compare
Resilient Seat Gate Valve-AWWA
Added to wishlistRemoved from wishlist 0
Add to compare
Resilient Seat Gate Valve-SOCKET
Added to wishlistRemoved from wishlist 0
Add to compare
Metal Seat Cast Iron Gate Valve-DIN
Added to wishlistRemoved from wishlist 0
Add to compare
Metal Seat Cast Iron Gate Valve-MSS
Added to wishlistRemoved from wishlist 0
Add to compare
Metal Seat Cast Iron Gate Valve-JIS
Added to wishlistRemoved from wishlist 0
Add to compare
Cast Steel Check Valve-DIN

LUCKY6S is Chinese leading manufacturer and supplier of industrial valves. which has over ten years of experience in manufacturing high-quality industrial valves, focuses on delivering safety, efficiency, and cost-effectiveness to every industry that requires automation. We are committed to supplying premium industrial valves and equipment to distributors, importers, and project managers worldwide. 

Top Valve Manufacturer

Newsletter

© 2018 All rights lucky6s

lucky6s-Best Valve manufacturer
Logo
Enable registration in settings - general
Compare items
  • Total (0)
Compare
0
Shopping cart